|
Instrumentation is the use of measuring instruments to monitor and control a process. It is the art and science of measurement and control of process variables within a production, laboratory, or manufacturing area. An instrument is a device that measures a physical quantity such as flow, temperature, level, distance, angle, or pressure. Instruments may be as simple as direct reading thermometers or may be complex multi-variable process analyzers. Instruments are often part of a control system in refineries, factories, and vehicles. The control of processes is one of the main branches of applied instrumentation. Instrumentation can also refer to handheld devices that measure some desired variable. Diverse handheld instrumentation is common in laboratories, but can be found in the household as well. For example, a smoke detector is a common instrument found in most western homes. Instruments attached to a control system may provide signals used to operate solenoids, valves, regulators, circuit breakers, or relays. These devices control a desired output variable, and provide either remote or automated control capabilities. These are often referred to as final control elements when controlled remotely or by a control system. A transmitter is a device that produces an output signal, often in the form of a 4–20 mA electrical current signal, although many other options using voltage, frequency, pressure, or ethernet are possible. This signal can be used for informational purposes, or it can be sent to a PLC, DCS, SCADA system, LabVIEW or other type of computerized controller, where it can be interpreted into readable values and used to control other devices and processes in the system. Control instrumentation plays a significant role in both gathering information from the field and changing the field parameters, and as such are a key part of control loops. == History == Elements of industrial instrumentation have long histories. Scales for comparing weights and simple pointers to indicate position are ancient technologies. Some of the earliest measurements were of time. One of the oldest water clocks was found in the tomb of the Egyptian pharaoh Amenhotep I, buried around 1500 BCE.〔(【引用サイトリンク】 url = http://www.nist.gov/pml/general/time/early.cfm ) 〕 Improvements were incorporated in the clocks. By 270 BCE they had the rudiments of an automatic control system device.〔 (【引用サイトリンク】 url = http://www.building-automation-consultants.com/building-automation-history.html ) 〕 In 1663 Christopher Wren presented the Royal Society with a design for a "weather clock". A drawing shows meteorological sensors moving pens over paper driven by clockwork. Such devices did not become standard in meteorology for two centuries.〔 United States National Museum, Bulletin 228. Contributions from The Museum of History and Technology: Paper 23. Available from Project Gutenberg.〕 The concept has remained virtually unchanged as evidenced by pneumatic chart recorders, where a pressurized bellows displaces a pen. Integrating sensors, displays, recorders and controls was uncommon until the industrial revolution, limited by both need and practicality. In the early years of process control, process indicators and control elements such as valves were monitored by an operator that walked around the unit adjusting the valves to obtain the desired temperatures, pressures, and flows. As technology evolved pneumatic controllers were invented and mounted in the field that monitored the process and controlled the valves. This reduced the amount of time process operators were needed to monitor the process. Later years the actual controllers were moved to a central room and signals were sent into the control room to monitor the process and outputs signals were sent to the final control element such as a valve to adjust the process as needed. These controllers and indicators were mounted on a wall called a control board. The operators stood in front of this board walking back and forth monitoring the process indicators. This again reduced the number and amount of time process operators were needed to walk around the units. The most standard pneumatic signal level used during these years was 3-15 psig.〔 〕 Electronics enabled wiring to replace pipes. The transistor was commercialized by the mid-1950s.〔http://ieeexplore.ieee.org/xpl/login.jsp?tp=&arnumber=704244&url=http%3A%2F%2Fieeexplore.ieee.org%2Fxpls%2Fabs_all.jsp%3Farnumber%3D704244〕 Each instrument company introduced their own standard instrumentation signal, causing confusion until the 4-20 mA range was used as the standard electronic instrument signal for transmitters and valves. This signal was eventually standardized as ANSI/ISA S50, “Compatibility of Analog Signals for Electronic Industrial Process Instruments", in the 1970s. The transformation of instrumentation from mechanical pneumatic transmitters, controllers, and valves to electronic instruments reduced maintenance costs as electronic instruments were more dependable than mechanical instruments. This also increased efficiency and production due to their increase in accuracy. Pneumatics enjoyed some advantages, being favored in corrosive and explosive atmospheres.〔 〕 The pneumatic and electronic signaling standards allowed centralized monitoring and control of a distributed process. The concept was limited by communication line lengths (perhaps 100 meters for pneumatics). Each pipe or wire pair carried one signal. The next evolution of instrumentation came with the production of Distributed Control Systems (DCS) which allowed monitoring and control from multiple locations which could be widely separated. A process operator could sit in front of a screen (no longer a control board) and monitor thousands of points throughout a large complex. A closely related development was termed “Supervisory Control and Data Acquisition” (SCADA). These technologies were supported by personal computers, networks and graphical user interfaces. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「instrumentation」の詳細全文を読む スポンサード リンク
|