翻訳と辞書
Words near each other
・ Iso Omena
・ Iso Rae
・ ISO Recorder Power Toy
・ Iso Rivolta IR 300
・ ISO RTO
・ ISO screw thread
・ ISO Standards for colour ink jet printers
・ ISO standards for trailer connectors
・ Iso suomen kielioppi
・ Iso Szajewicz
・ ISO TC 279
・ Iso Varedo
・ ISO week date
・ ISO-8859-8-I
・ Iso-damping
Iso-elastic
・ Iso-Heikkilä
・ Iso-Heikkilä Observatory
・ ISO-IR-165
・ Iso-Kiimanen
・ Iso-Naakkima
・ Iso-Polifonia
・ Iso-Pyhäntä
・ Iso-Roine
・ Iso-Syöte
・ ISO-TimeML
・ Iso-Vietonen
・ ISO/IEC 10021
・ ISO/IEC 10116
・ ISO/IEC 10967


Dictionary Lists
翻訳と辞書 辞書検索 [ 開発暫定版 ]
スポンサード リンク

Iso-elastic : ウィキペディア英語版
Iso-elastic

In engineering, iso-elastic refers to a system of elastic and tensile parts (springs and pulleys) which are arranged in a configuration which serves to isolate physical motion at one end from affecting the same motion at the other end.
This type of device must be able to maintain angular direction and load-bearing over a large range of motion.
The most prominent use of an iso-elastic system is in the supporting armature of a Steadicam.
The Steadicam arm is used to isolate a film or video camera from the operator's movements.
Steadicam arms all work in a fashion similar to a spring lamp since each arm has 2 sections (similar to and labelled like a human arm), both the upper and fore-arm sections consist of a parallelogram with diagonal iso-elastic cable-pulley-spring system. The iso-elastic system is tensioned to counteract the weight of the camera and steadicam sled. This tensioning allows the camera and operator to move vertically and independently of each other. For example as the operator runs, the bouncing of his body is absorbed by the springs, keeping the camera steady. The arm also has unsprung hinges at both ends of each arm allowing it to bend in the horizontal plane (just like your elbow, not like a spring lamp).
To understand how an iso-elastic system works, we must first understand how springs work. The tension (elastic force) in a spring is proportional to its extension according to Hooke's law. This means that if a weight is hung on a spring it will oscillate with simple harmonic motion. This is because when the weight is above the balance point, the spring's tension is reduced so the weight falls due to gravity, and when the weight is below the balance point the spring's tension will pull it back upwards.
If a simple spring system were used in a steadicam, then if the operator moved vertically, the camera would execute simple harmonic motion, and bounce up and down. Instead, an iso-elastic system is employed.
The springs used are large, stiff springs with a high modulus of elasticity, and they are highly tensioned. A compound pulley system is then used so that the large force exerted by the spring can be divided by a factor of (say) five. The cable exiting the pulley system will have a moderate tension on it, but most importantly, when the cable is drawn in or out, and the extension of the spring changes by only a fifth of that distance, so that the tension force of the spring will not change much. The result is that the spring-pulley system can produce a fairly constant tension in the cable over a large range of movement.
The almost constant force exerted by an iso-elastic system is employed in the armature of a steadicam, to counteract the constant force of gravity on the camera's and mount's mass. The result is that the weight of the camera is almost exactly balanced by the tension force throughout the entire range of vertical movement, so even when the operator jumps vertically, the camera will retain its vertical position due to inertia, but remain balanced, just with the armature at a different angle.
As a result the camera doesn't bounce up to the 'balanced' position after a move, for example when the operator steps up onto a curb from the road. This allows the camera to be more isolated and independent of the operator's moves. The operator can of course deliberately move the camera up or down, if desired. In reality however camera operators find it preferable for the arm to not be perfectly iso-elastic so that the camera will naturally rise to a comfortable operating height. Though the springs will be tensioned so this only happens very slowly and without bouncing up and down so as to maintain the smoothness of the camera's motion."〔Adustable, iso-elastic support apparatus
US 5435515 A.〕
== See also ==

* Precision engineering

抄文引用元・出典: フリー百科事典『 ウィキペディア(Wikipedia)
ウィキペディアで「Iso-elastic」の詳細全文を読む



スポンサード リンク
翻訳と辞書 : 翻訳のためのインターネットリソース

Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.